1FORM NO. L-20150-V-1112Flange Mounted Enclosed Clutch-BrakesModels 625, 875, 1125 and 1375AIR CHAMP PRODUCTSUser Manual
10FORM NO. L-20150-V-1112 PARTS REPLACEMENT / FRICTION FACINGSTABLE 2MODELS 625, 875, 1125, AND 13751. Remove the four Socket Head Cap Screws (Ite
11FORM NO. L-20150-V-1112 PARTS REPLACEMENT / BALL BEARINGNOTE: The following sections are arranged by model. Verify that you are in the correct se
12FORM NO. L-20150-V-1112MODELS 875, 1125, AND 1375 FEMALE PILOTNOTE: If an Input Unit is installed on the FMCBE, it must be removed before servici
13FORM NO. L-20150-V-1112MODELS 875, 1125, AND 1375 FEMALE PILOT(continued)12. Support the inner race of the new Ball Bearing (Item 2) and press the
14FORM NO. L-20150-V-1112PARTS REPLACEMENT / PISTON, DRIVE DISC, BEARINGS, AND O-RING SEALS (continued)6. Clean the bearing bore of the Male Pilot
15FORM NO. L-20150-V-1112PARTS REPLACEMENT / PISTON, DRIVE DISC, BEARINGS, AND O-RING SEALS (continued)23. Lubricate the new O-ring Seals (Items 21
16FORM NO. L-20150-V-1112 REPLACEMENT PARTSThe item or balloon number for all Nexen products is used for part identification on all product parts list
17FORM NO. L-20150-V-1112 ITEM DESCRIPTION QTY 173 Spring Pin 1 183 Retaining Ring (Int.) 1 191 Ball Bearing 2 20 Male Pilot 1 211 O-r
18FORM NO. L-20150-V-1112 ITEM DESCRIPTION QTY 183 Retaining Ring (Int.) 2 191 Ball Bearing 2 20 Male Pilot 1 211 O-ring Seal 1 221
19FORM NO. L-20150-V-1112 ITEM DESCRIPTION QTY 1 Housing 1 21 Ball Bearing 2 3 Retaining Ring (Int.) 2 4 Drive Disc 1 5 Retaining Ring
2FORM NO. L-20150-V-1112Copyright 2012 Nexen Group, Inc.Nexen Group, Inc.560 Oak Grove ParkwayVadnais Heights, Minnesota 55127ISO 9001 CertifiedThis do
20FORM NO. L-20150-V-1112 ITEM DESCRIPTION QTY 1 Housing 1 21 Ball Bearing 2 3 Retaining Ring (Int.) 2 4 Drive Disc 1 5 Retaining Ring
21FORM NO. L-20150-V-1112 ITEM DESCRIPTION QTY 11 Stub Shaft 1 19 Key 2 20 Bearing Flange 1 30 Ball Bearing 2
22FORM NO. L-20150-V-1112Nexen Group, Inc.560 Oak Grove ParkwayVadnais Heights, MN 55127800.843.7445Fax: 651.286.1099www.nexengroup.comISO 9001 Certi
3FORM NO. L-20150-V-1112 TABLE OF CONTENTSGeneral Specifications -------------------------------------------------------------------------------------
4FORM NO. L-20150-V-1112GENERAL SPECIFICATIONSGENERAL SAFETY PRECAUTIONSCAUTIONCAUTIONUse lifting aids and proper lifting techniques when installing,
5FORM NO. L-20150-V-1112 INSTALLATIONMOUNTING ON THE SHAFT END OF A MOTORNOTE: Model 625 does not have a Female Pilot (Item 26); proceed with Step 2
6FORM NO. L-20150-V-1112MOUNTING BETWEEN A GEAR REDUCER AND A MOTOR1. Insert the Key (Item 25) into the output shaft of the FMCBE (See Figure 3).2.
7FORM NO. L-20150-V-1112NOTENexen pneumatically actuated devices require clean, pressure regulated air for maximum performance and life. All seals in
8FORM NO. L-20150-V-11123/2 (3 Way)4/2 (4 Way)5/2 (4 Way)5/2 (5 Way)AIR CONNECTIONSNOTEFor quick response, Nexen recommends a quick exhaust valve and
9FORM NO. L-20150-V-1112 TROUBLESHOOTINGMOTPMYS ESUACELBABORP NOITULOS.egagneoteruliaFaoteudEBCMFehtotgnittegtonriA.noitcnuflamevlavlortnocronoitcnufl
Comments to this Manuals