1FORM NO. L-20250-E-0114FMCBE 625 and 875 Clutch-BrakesBISSC CertifiedWith and Without Locking KeyFORM NO. L-20250-E-0114
10FORM NO. L-20250-E-0114TROUBLESHOOTINGHousingPistonBearingsBearingStub ShaftDrive DiscO-RingSealFemale PilotMale PilotO-Ring SealsFriction FacingSpl
11FORM NO. L-20250-E-0114Refer to Figure 11. 1. Remove the eight Hex. Head Cap Screws (Item 27), Female Pilot (Item 34), Drive Disc (Item 4), and O-R
12FORM NO. L-20250-E-0114Refer to Figures 12 & 13. 1. Remove the Retaining Ring (Item 6).2. Supporting the inner flange of the Housing (Item 1),
13FORM NO. L-20250-E-0114Refer to Figures 14 & 15. 1. Remove the Key (Item 25).2. Remove the Retaining Ring (Item 24).3. Press the Stub Shaft (
14FORM NO. L-20250-E-0114FEMALE PILOT BEARING (Item 2) AND O-RING SEAL (Item 33)Refer to Figures 16 & 17. 1. Remove the Retaining Ring (Item 6) f
15FORM NO. L-20250-E-0114INPUT UNITRefer to Figures 18 - 20. 1. Remove the eight Hex. Head Cap Screws (Item 27).2. Remove the four Hex. Head Cap Scr
16FORM NO. L-20250-E-01141615142717236222119201819241363433322674511102325711FIGURE 2111 Denotes Rebuild Kit item. Rebuild Kit Product No. 827252ITE
17FORM NO. L-20250-E-0114FIGURE 22621320635911193058351935INPUT UNITMOUNTING FOOT7171FIGURE 237073757677731 Denotes Repair Kit item. Repair Kit Pro
18FORM NO. L-20250-E-0114Nexen Group, Inc.560 Oak Grove ParkwayVadnais Heights, MN 55127800.843.7445Fax: 651.286.1099www.nexengroup.comISO 9001 Certi
2FORM NO. L-20250-E-0114Copyright 2014 Nexen Group, Inc.Nexen Group, Inc.560 Oak Grove ParkwayVadnais Heights, Minnesota 55127ISO 9001 CertifiedThis do
3FORM NO. L-20250-E-0114Table of ContentsGeneral Specifications ---------------------------------------------------------------------------------------
4FORM NO. L-20250-E-0114GENERAL SPECIFICATIONSGENERAL SAFETY PRECAUTIONSCAUTIONUse lifting aids and proper lifting techniques when installing, removin
5FORM NO. L-20250-E-0114NOTEAlign the air inlet ports to a down position to allow condensation to drain out of the ports.1. Insert customer supplied
6FORM NO. L-20250-E-0114Align the air inlet ports to a down position to allow condensation to drain out of the ports.Refer to Figure 3. 1. Insert cus
7FORM NO. L-20250-E-0114OPTIONAL MOUNTING FEETRefer to Figure 5. 1. Coat the O-Ring Seal (Item 59) and the seal contact surface of the Input Unit wit
8FORM NO. L-20250-E-0114NOTENexen pneumatically actuated devices require clean, pressure regulated air for maximum performance and life. All seals in
9FORM NO. L-20250-E-01143/2 (3 Way)4/2 (4 Way)5/2 (4 Way)5/2 (5 Way)AIR CONNECTIONS NOTEFor quick response, Nexen recommends a quick exhaust valve a
Comments to this Manuals